Recent Activity
Activity stream for all registered members at OpenBuilds.
-
David the swarfer liked Peter Van Der Walt's post in the thread X axis getting stuck.
1) During the crash something may have become moved, bent or damaged: Perform a check on all the mechanicals making sure its all...
Oct 15, 2024 at 3:03 AM -
Gary Caruso liked Mark Carew's post in the thread Prayers..
We made it! It was a crazy storm for sure and we thank you all for the prayers! There is so much widespread damage it's crazy! I have...
Oct 14, 2024 at 7:04 PM
-
Gary Caruso liked Mark Carew's post in the thread Prayers..
and were back! We have power back at HQ and are ready to get back to it! Thank you all again for your prayers, we appreciate you all....
Oct 14, 2024 at 7:04 PM -
Giarc liked Peter Van Der Walt's post in the thread Blackbox x32 trying to run inventables easel.
Use easel to generate gcode: https://inventables.zendesk.com/hc/en-us/articles/4406926040979-Exporting-Gcode-From-Easel Then run it as...
Oct 14, 2024 at 4:32 PM -
Mark Carew replied to the thread Prayers..
and were back! We have power back at HQ and are ready to get back to it! Thank you all again for your prayers, we appreciate you all....
Oct 14, 2024 at 7:36 AM -
David the swarfer liked Peter Van Der Walt's post in the thread Blackbox x32 trying to run inventables easel.
Use easel to generate gcode: https://inventables.zendesk.com/hc/en-us/articles/4406926040979-Exporting-Gcode-From-Easel Then run it as...
Oct 14, 2024 at 2:31 AM -
David the swarfer replied to the thread X axis getting stuck.
that leadscrew is much too tight, check the nut adjustments, and alignment etc. also the bearings on the ends of course. remember to...
Oct 14, 2024 at 2:31 AM -
David the swarfer replied to the thread X axis getting stuck.
my X had some sticky spots (a screw head was hitting the rail, sometimes) and I had to do a combination of slowing down the axis (both...
Oct 13, 2024 at 12:35 PM -
David the swarfer replied to the thread x32 z limit switch stays triggered.
pity, could be as simple as inverting the sense of the switch, the box caters for both normally closed and normally open switches, but...
Oct 13, 2024 at 12:32 PM -
Giarc liked dJOS_500's post in the thread Upgraded 3018 Pro using MGN15H Linear Rails and a 500w Spindle.
My electrical cabinet now has an eStop / power switch. I’m waiting for some wiring glands to arrive before I add the power cable. I was...
Oct 13, 2024 at 12:05 PM
-
David the swarfer liked Mark Carew's post in the thread Prayers..
We made it! It was a crazy storm for sure and we thank you all for the prayers! There is so much widespread damage it's crazy! I have...
Oct 11, 2024 at 3:00 AM
-
Dennis Huddleston posted a new thread.
Software
What software will work with the BlackBox Motion Control System X32?
Forum: CNC Mills/Routers
Oct 10, 2024 at 9:22 PM -
Rick 2.0 liked Mark Carew's post in the thread Prayers..
We made it! It was a crazy storm for sure and we thank you all for the prayers! There is so much widespread damage it's crazy! I have...
Oct 10, 2024 at 7:56 PM
-
Mark Carew attached a file to the thread Prayers..
We made it! It was a crazy storm for sure and we thank you all for the prayers! There is so much widespread damage it's crazy! I have...
Oct 10, 2024 at 3:40 PM