Welcome to Our Community

Some features disabled for guests. Register Today.

DB25-1205 Breakout Board

Discussion in 'CNC Mills/Routers' started by Cornerspace, Sep 16, 2017.

  1. Cornerspace

    Builder

    Joined:
    Oct 2, 2016
    Messages:
    57
    Likes Received:
    2
    Got the 4 axis Nema23 Kit from Longs Motor. Came with the above as the interface. Question how do I power it up? Can I connect it to the 36V PSU? It draws only 5V and am concerned about it blowing the board. Am also confused by the pin out as the board is not very clear on that front and how to hook it up the the DM542 Stepper Drivers. Any advice is appreciated. :) Thanks.
     
  2. Joe Santarsiero

    Joe Santarsiero OB addict
    Staff Member Moderator Builder

    Joined:
    Oct 30, 2014
    Messages:
    902
    Likes Received:
    196
    Hi Cornerspace,
    You'll have to give it its own 5v from somewhere. You could use a wall transformer, a usb port, or a small 5v supply similar to the 36v you have.
    If you want to get fancy you can use the 36v supply, but you'll have to make a voltage reduction circuit. Reducing voltage with resistors
     
  3. Cornerspace

    Builder

    Joined:
    Oct 2, 2016
    Messages:
    57
    Likes Received:
    2
    Thanks. I managed to find a old 5V PSU. It setup for Single power supply by default. Trying to configure the Mach 3 software. :( Any experience on using the setup with a Parallel to USB adaptor as opposed to a Parallel Card? I think this might be the cause of my problems as the USB part needs to be configured as the card is not detected when i hook everything up.
     
  4. Gary Caruso

    Gary Caruso OpenBuilds Volunteer
    Staff Member Moderator Builder

    Joined:
    May 19, 2016
    Messages:
    1,193
    Likes Received:
    532
    Did you install the drivers for the adapter? does the adapter show up when you plug in the usb under device manager? parallel-usb adapters can be a craps shoot
     
    Joe Santarsiero likes this.
  5. Cornerspace

    Builder

    Joined:
    Oct 2, 2016
    Messages:
    57
    Likes Received:
    2
    Yup a definite crap shoot. The adapter is detected but the BOB isnt. What sorta setup are you using? Is your hooked up to a xPro? What in your opinion is a good starter? :) Ordering a 5VDC as the mobile supply seems a tad under powered.
     
  6. Gary Caruso

    Gary Caruso OpenBuilds Volunteer
    Staff Member Moderator Builder

    Joined:
    May 19, 2016
    Messages:
    1,193
    Likes Received:
    532
    I'm using the dq542ma drives, with an Arduino Uno and GRBL.. just make sure to get a real Arduino they are like $16
     
  7. Joe Santarsiero

    Joe Santarsiero OB addict
    Staff Member Moderator Builder

    Joined:
    Oct 30, 2014
    Messages:
    902
    Likes Received:
    196
    You'll need an adapter like the UC100. If you can afford a smoothstepper I would go that route though.

    Here's an Openbuilds thread on this subject.
    USB To DB25 Adapter Help and Creating LPT Port for Mach3
     
  8. ChadRat6458

    Builder

    Joined:
    Dec 10, 2014
    Messages:
    93
    Likes Received:
    24
    I like this for 5v. You can connect it to your 36v power supply Module Voltage Regulator Step-Down Converter 4.0~40 To 1.3-37V Power Module | eBay I just ordered the Long Motor kit. I have a similar set up on my ox. I am now building a sphinx. I run LinuxCNC on an old dell optiplex with a built in parallel port. You can get these for almost nothing. Works well and I don't care if it gets covered in saw dust. I keep my nice laptop in the house for CAD and modeling.
     
    Cornerspace and Joe Santarsiero like this.
  9. Cornerspace

    Builder

    Joined:
    Oct 2, 2016
    Messages:
    57
    Likes Received:
    2
    Thanks for the great advice. Cheaped out and got myself a clone UNO. Had some troubleshooting to find the right driver for the board (Uses a CH340 chip). Am figuring the best UI to use for generating the GCode. What is the preferred method for you guys? :)
     
    #9 Cornerspace, Sep 26, 2017
    Last edited: Sep 26, 2017
  10. Gary Caruso

    Gary Caruso OpenBuilds Volunteer
    Staff Member Moderator Builder

    Joined:
    May 19, 2016
    Messages:
    1,193
    Likes Received:
    532
    I don't know how true it is but most people will say the true Uno has better luck with data rates. You might have issues with the clone. The real thing should be about $16, lots of gouging out there too i found.
    on amazon, looks real at least
     
    Cornerspace likes this.
  11. Gary Caruso

    Gary Caruso OpenBuilds Volunteer
    Staff Member Moderator Builder

    Joined:
    May 19, 2016
    Messages:
    1,193
    Likes Received:
    532
  12. Cornerspace

    Builder

    Joined:
    Oct 2, 2016
    Messages:
    57
    Likes Received:
    2
    Finally got the Z axis working. :)
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice