Welcome to Our Community

Some features disabled for guests. Register Today.

V-slot wheel (/weight) orientation : vertical vs horizontal

Discussion in 'General Talk' started by Agamemnon, Jun 30, 2014.

  1. Agamemnon

    Agamemnon New
    Builder

    Joined:
    Apr 25, 2014
    Messages:
    12
    Likes Received:
    2
    Hi folks,

    Here's a quick question about v-slot wheel orientation:
    Can they be used horizontally instead of the usual vertical orientation?

    What do I mean?
    Vertical = the standard gantry type router builds like the Ox.
    The wheels ride above and below the rail; mounted on a plate that is parallel with the rail in an upright position. The weight of the gantry pushes the top wheels down into the middle of the rail slot, applying pressure to both edges of the wheel. The wheels on the bottom don't hold gantry load, and act as stabilisers.

    Horizontal = an atypical setup, virtually the opposite of vertical.
    I want to know if you can think of any reasons why I shouldn't do it this way - because this is my preference!
    To be clear : the mounting plate will be oriented horizontally; as is the rail. The wheels will be on the sides of the rail (rather than top/bottom), and the load will be applying pressure to only the bottom sides of the wheels. [Relatively, there will be twice as many wheels under load, as all wheels in the assembly are loaded.]

    How much load are we talking about?
    I expect roughly 25lbs / 10kg. The wheels are the solid delrin type, rather than the v-wheel.

    Appreciate your consideration!
     
  2. Wizzard

    Wizzard New
    Builder

    Joined:
    Jul 2, 2014
    Messages:
    1
    Likes Received:
    0
    Hi

    I should start with I'm not a structural engineer! My understanding of the bearings in the Wheel setup used by the V-slots is that they are internally designed to take weight on the plane perpendicular to the axle and not from the side in line with the axle. Using them the way you describe would put the main load on the side of the bearings if I understood your description.

    hope that helps
     
  3. Rick 2.0

    Rick 2.0 OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Dec 20, 2013
    Messages:
    2,892
    Likes Received:
    1,549
    Actually this is more of a mechanical engineering issue than a structural one. Bearings are designed to handle a small amount of lateral force but how much is hard to say. It's likely a function of the depth of the groove the balls ride in. Testing may be the only way to get to the answers you seek.
     
  4. Agamemnon

    Agamemnon New
    Builder

    Joined:
    Apr 25, 2014
    Messages:
    12
    Likes Received:
    2
    Rick and Wizzard, many thanks for your thoughts. You are clearly correct in identifying the bearing specifications in investigating this issue!
     
  5. Duane

    Duane New
    Builder

    Joined:
    May 19, 2014
    Messages:
    23
    Likes Received:
    3
  6. Lee Saferite

    Builder

    Joined:
    Apr 29, 2014
    Messages:
    32
    Likes Received:
    5
    You are talking about radial vs axial load on the bearings.

    The standard usage is to load the bearings radially and most bearings are designed for this. You want to use them with an axial load and the bearings you have are mostly probably not rated for much, if any, axial load.

    One thing I've seen done is to use three contacts points. A top bearing is the one handling all the actual load with the side bearings doing guide work. (Which, not that I re-read, is what @Duane said)
     
  7. Duane

    Duane New
    Builder

    Joined:
    May 19, 2014
    Messages:
    23
    Likes Received:
    3
    I came across a product called the Zenslider today. From the limited information on the the site it appears to use v-slot and solid delrin as the guide. Again, I have no idea how much weight this would handle but seems to work okay with various size cameras.

    http://zenslider.com/zenslider/

    Does anyone know what would be involved in machining or extruding delrin to match the extrusion profile?
     
  8. andrew

    andrew New
    Builder

    Joined:
    Mar 16, 2014
    Messages:
    47
    Likes Received:
    18
    Duane - Check out SlideRap. I think the slider idea could work well for light load situations. I've got a piece of delrin I may experiment with. May require lubrication. PTFE could work well dry.

    As far as horizontal wheels go, I think it's fine with a light load. Angular contact bearings in the wheels would better handle the axial load, but hard to find in that size and probably too expensive.
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice