Welcome to Our Community

Some features disabled for guests. Register Today.

OpenBot

Discussion in '3D printers' started by Midgetmountain, Jun 2, 2014.

  1. Midgetmountain

    Builder

    Joined:
    Jun 2, 2014
    Messages:
    3
    Likes Received:
    15
    Midgetmountain published a new build:

    Read more about this build...
     
  2. Tweakie

    Tweakie OpenBuilds Team
    Moderator

    Joined:
    Jan 18, 2014
    Messages:
    784
    Likes Received:
    326
    Hey @Midgetmountain that build looks really great.

    Just wondering, do you get enough rigidity with the open ended rail design as I can imagine a bit of wobble at the extremes if a high rate of axis acceleration is used ?

    Tweakie.
     
  3. angelo

    angelo New
    Builder

    Joined:
    May 26, 2014
    Messages:
    16
    Likes Received:
    4
    great job
     
  4. Midgetmountain

    Builder

    Joined:
    Jun 2, 2014
    Messages:
    3
    Likes Received:
    15
    Hey Tweakie,

    There is little amount of wobble in the boom (if I move it by hand), but it is surprisingly stiff in fast acceleration. At the moment I have two issues with my design, the build platform mounting (that should be fixed once I can get my hands on a openbuild build platform), and plates mounted on the v-slot moving.

    Its still a work in progress.
     
  5. Keith Davis

    Keith Davis Veteran
    Builder

    Joined:
    Dec 11, 2013
    Messages:
    507
    Likes Received:
    398
    Midgetmountain, that looks a lot like a design I did earlier this spring. Problem I had was keeping the x axis arm parallel to the y axis. I looked at Bukobot's Bukito design and saw the solution. Their plate that runs up the vertical frame piece and carries the x axis arm has only 3 wheels. Mine had 4 wheels. They had 1 adjuster wheel on one side and the two stationary ones on the opposite side. That creates a triangle wheel design (actually stronger than a 4 sided design). Adjusting the one wheel automatically squares the x axis bar with the y axis, if everything else is square.Your design shows 4 wheels on that vertical axis bar. Try 3.

    Here's a picture of my opnbot design. [​IMG]
     
    Seul Kee and Robert Hummel like this.
  6. Midgetmountain

    Builder

    Joined:
    Jun 2, 2014
    Messages:
    3
    Likes Received:
    15
    Hey Keith,

    Thanks for the feedback.

    There are few problems the current design, that I need to fix. The biggest pain is the plate mounted on the v-slot can slip, making it fun keeping everything aligned. I am going to print a block for the boom to keep it level, and another one for the base to keep it square. Another issue is how I have the build-platform supported (currently used some wooden slates), but when I can get an openbuilds build platform that should fix that up. I am also designing a extruder holder with a force sensor built in, so I can do auto bed levelling.

    Below is my first concept, similar to your BldrBot (Which I really like!). I cut this design down so I could keep the parts count down, I was worried that the single 20x20 boom would not be that sturdy, but it surprised me.

    [​IMG]
     
  7. raykholo

    raykholo New
    Builder

    Joined:
    Jun 29, 2014
    Messages:
    38
    Likes Received:
    4
    This looks a lot like a design I'm working on right now except in mine the bed is stationary and the arm assembly will move in all 3 axes, so it's a bit more OX/ Routy like as well. Build log to come soon.
     
  8. jlipavsky79

    Builder

    Joined:
    Jan 9, 2016
    Messages:
    4
    Likes Received:
    1
    there seems to be no picture or files to this, is it still active or has this been an abandoned project?
     
    Oleks likes this.

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice