Welcome to Our Community

Some features disabled for guests. Register Today.

Ooznest ox with LinuxCNC

Discussion in 'CNC Mills/Routers' started by Pops, May 18, 2016.

  1. Pops

    Pops New
    Builder

    Joined:
    Nov 24, 2015
    Messages:
    15
    Likes Received:
    3
    Hi All

    I have my ooznest ox built. The instructions were fantastic and I had less trouble building it than I did a gas Bbq. I'm very impressed.

    Ox build it 1m x 1.5m. Nema 23s.

    To that I have added a gecko g540 and an old PC with Linux cnc installed. Getting it to communicate with the machine was easier than I expected in that by following the instructions with the g540 and taking default values and a little common sense when setting up linuxcnc it just worked.

    My questions are now down to tuning things. What experience have people had with this setup? Specifically, does anyone have suggestions for optimal settings for max speed and acceleration for the three axes?

    I have a little way to go before I cut anything but progress so far has been reasonably straight forward and I hope continues this way.

    Thanks to you all.

    Ivan
     
  2. Ryan Lock

    Ryan Lock Veteran
    Builder

    Joined:
    Oct 12, 2014
    Messages:
    530
    Likes Received:
    293
    Hi,

    I haven't got a setup for linuxcnc, but i have attached my GRBL Settings if they are of any help.

    Ryan
     

    Attached Files:

  3. Pops

    Pops New
    Builder

    Joined:
    Nov 24, 2015
    Messages:
    15
    Likes Received:
    3
    Ryan,

    Thanks, that's perfect. I suspect max rate and acceleration are not Linux cnc specific anyway.
     
  4. ChadRat6458

    Builder

    Joined:
    Dec 10, 2014
    Messages:
    93
    Likes Received:
    24
    How are things going? I am in the same boat. I am trying to tune my linuxcnc setup. I can cut but I am missing steps big time.
     
  5. Pops

    Pops New
    Builder

    Joined:
    Nov 24, 2015
    Messages:
    15
    Likes Received:
    3

    Hi. It's going very well. I have some fine tuning for each of the axes but no missed steps. I suspect missed steps are more to do with your driver board. I have not really pushed the machine yet but the cuts I have made seem to be regular and repeatable. What driver board setup did you use? I'm very happy with the gecko driver it's pricey but good.
     
  6. ChadRat6458

    Builder

    Joined:
    Dec 10, 2014
    Messages:
    93
    Likes Received:
    24
  7. Pops

    Pops New
    Builder

    Joined:
    Nov 24, 2015
    Messages:
    15
    Likes Received:
    3
  8. ChadRat6458

    Builder

    Joined:
    Dec 10, 2014
    Messages:
    93
    Likes Received:
    24
    I checked my wires going to the x axis motor with a multimeter. They checked out fine. I put them back in and it is working a lot better. I guess I had one wire not making a good connection. They were all tight. I would still like to see your files so I can compare them to mine. Thanks.
     
  9. Pops

    Pops New
    Builder

    Joined:
    Nov 24, 2015
    Messages:
    15
    Likes Received:
    3
    Thats great you have it working. I could not get stepconf to do the right thing with my limit switches so I had to tweak the files for that. Other than that they come straight from stepconf.
     
  10. ChadRat6458

    Builder

    Joined:
    Dec 10, 2014
    Messages:
    93
    Likes Received:
    24
    I had a loose x axis pulley. I want to change my x axis to a lead screw set up. Excuse for a bigger machine? I really like how linuxCNC works. The drivers are working great.
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice