Welcome to Our Community

Some features disabled for guests. Register Today.

Laser V

Discussion in 'Laser Cutters' started by Robert Hummel, Nov 30, 2013.

  1. Woodie49

    Woodie49 New
    Builder

    Joined:
    Feb 7, 2014
    Messages:
    61
    Likes Received:
    1
    I'm useing the Mini V Wheel Kit, spacer & ect. Every thing is square.
    It does look like some of the V wheel aren't hiting the top and bottom of the V groove.
    I did get the Y axis wheels to move good.
     
  2. Tweakie

    Tweakie OpenBuilds Team
    Moderator

    Joined:
    Jan 18, 2014
    Messages:
    784
    Likes Received:
    326
    Sounds like something is not plumb.
    Is it possible that the dimensional width of the gantry does not exactly match the dimensional width of the frame - as far as the V-Wheels / V-Slots are concerned ? In which case additional shims / spacers may improve the situation.

    Tweakie.
     
  3. JCPhlux

    JCPhlux Well-Known
    Builder

    Joined:
    Apr 19, 2014
    Messages:
    209
    Likes Received:
    48
    What plates are you using?
     
  4. JCPhlux

    JCPhlux Well-Known
    Builder

    Joined:
    Apr 19, 2014
    Messages:
    209
    Likes Received:
    48
    I am getting excited my parts are one day out. :D
     
  5. Woodie49

    Woodie49 New
    Builder

    Joined:
    Feb 7, 2014
    Messages:
    61
    Likes Received:
    1
    The Plates I got from Robert.
     
  6. Wojtek

    Wojtek New
    Builder

    Joined:
    Apr 29, 2014
    Messages:
    32
    Likes Received:
    0
    i am at the moment designing the case for the laser cutter. what should the minimum hight of it be
     
  7. skarab

    skarab Journeyman
    Builder

    Joined:
    Jan 5, 2014
    Messages:
    96
    Likes Received:
    141
    I still had some 20x40 aluminum profile and 20x20x1000mm v-slot from my last build. Your project running through my head for a while. Pending the material for the OX, I started a laser router wickedly inspired by your construction.

    2014-05-26 17.29.05.jpg

    Thank you for sharing :D
     
    Robert Hummel likes this.
  8. JCPhlux

    JCPhlux Well-Known
    Builder

    Joined:
    Apr 19, 2014
    Messages:
    209
    Likes Received:
    48
    looks good.
    I finally got all my parts in but have a 4 week contract that really needed 8 weeks so I have to put my build on hold.
     
  9. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    I hope that means your care package made it :)
     
  10. JCPhlux

    JCPhlux Well-Known
    Builder

    Joined:
    Apr 19, 2014
    Messages:
    209
    Likes Received:
    48
    Hey sorry Robert, I thought I sent you a msg. Go the package I have not had a chance to play wit any of it yet but it looks great.
     
  11. skarab

    skarab Journeyman
    Builder

    Joined:
    Jan 5, 2014
    Messages:
    96
    Likes Received:
    141
    Too happy :D A big thank to Robert Hummel for his build log, OpenBuilds and all the DIY community! Next the OX :thumbsup:
    2014-06-22 17.13.52.jpg 2014-06-22 17.12.35.jpg 2014-06-22 17.13.00.jpg 2014-06-22 17.28.40.jpg
     
    Mark Carew and Robert Hummel like this.
  12. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
  13. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,759
    Likes Received:
    2,438
    Well done @skarab :thumbsup: looks great!
     
  14. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    So after going through end user suggestions, the following updates have bin added to the laser V LD2X

    -Power indication LED
    -Relay is powered by 5v regulator rather then the arduino
    -Relay contact rating of 3 amps
    -Regulated 5v pin rail added along side of the negative pin rail
    -Manual laser on/off pin-out for a momentary switch beside the reset pin-out
    -Dual stepstick Y axis
    -Single stepstick X axis
    -Single stepstick Z axis added for laser focusing
    -RX/TX pin out

    Everything else is the same, board size was enlarged by 20 mm width wise.
    Again I have kept it single sided for easy DIY
    The updated file will be posted soon along with a parts list
     
    AlexUT, Mark Carew and skarab like this.
  15. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,759
    Likes Received:
    2,438
    Sounds great Robert! :thumbsup:
     
  16. JCPhlux

    JCPhlux Well-Known
    Builder

    Joined:
    Apr 19, 2014
    Messages:
    209
    Likes Received:
    48
    Ok, I am back. I am going to start my build tomorrow!
     
    skarab likes this.
  17. Woodie49

    Woodie49 New
    Builder

    Joined:
    Feb 7, 2014
    Messages:
    61
    Likes Received:
    1
    Has the updated file and parts list been posted yet?
    Thanks
     
  18. Pokry

    Pokry New
    Builder

    Joined:
    Aug 6, 2014
    Messages:
    5
    Likes Received:
    0
    Hi
    I have a question. Could someone draw a square and a circle in the program to generate g-code and add a file? I want to see what he looks like. Is he saved in txt format?
     
  19. bobt

    bobt Well-Known
    Builder

    Joined:
    Dec 4, 2013
    Messages:
    89
    Likes Received:
    38
  20. JCPhlux

    JCPhlux Well-Known
    Builder

    Joined:
    Apr 19, 2014
    Messages:
    209
    Likes Received:
    48
  21. Pokry

    Pokry New
    Builder

    Joined:
    Aug 6, 2014
    Messages:
    5
    Likes Received:
    0
    I am doing a project on stm32f401 and do not know how to program it is able to do different shapes.
     
  22. JCPhlux

    JCPhlux Well-Known
    Builder

    Joined:
    Apr 19, 2014
    Messages:
    209
    Likes Received:
    48
    What is stm32f401?
     
  23. Menneset

    Menneset New
    Builder

    Joined:
    Oct 15, 2014
    Messages:
    6
    Likes Received:
    2
    I was planning a laser cutter build and stumbled across this site and in particular this build. This is freaking awesome! This is one of--forget that, this is the best and most detailed build post I have seen. I am so pumped up right now, I gotta get to work on this...
     
    Robert Hummel likes this.
  24. JCPhlux

    JCPhlux Well-Known
    Builder

    Joined:
    Apr 19, 2014
    Messages:
    209
    Likes Received:
    48
    Very cool. Cant wait to see your build.
     
  25. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    New LD3X test board :D
    image.jpg
    Wiring and getting ready for full testing :thumbsup:
     
  26. AlexUT

    AlexUT New
    Builder

    Joined:
    Oct 8, 2014
    Messages:
    4
    Likes Received:
    0
  27. JCPhlux

    JCPhlux Well-Known
    Builder

    Joined:
    Apr 19, 2014
    Messages:
    209
    Likes Received:
    48
    very nice
     
  28. skarab

    skarab Journeyman
    Builder

    Joined:
    Jan 5, 2014
    Messages:
    96
    Likes Received:
    141
    2W Laser diod from eBay.
     
  29. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    Part number is M140
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice