Welcome to Our Community

Some features disabled for guests. Register Today.

HULK-XY (Fixed Build Plate, C-Beam, CoreXY)

Discussion in '3D printers' started by Adam Filipowicz, Sep 21, 2015.

  1. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
  2. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    What is that pause when the loop ends and starts back up?
     
  3. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
    the Z adjusts to the next layer. at that point, it was not set to vase mode.
     
  4. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    Ahhhh.
     
  5. hernejj

    hernejj New
    Builder

    Joined:
    Apr 10, 2016
    Messages:
    5
    Likes Received:
    0
    Looking good! I especially love the z-axis speed! My MakerFarm iv3 has a painfully slow lift speed. It leads to blobbing at the corners of my prints. Perhaps I should try and adjust it,
     
  6. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
    I do notice that it still pauses, running at 150mm/sec the rumba has trouble keeping up
     
  7. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    Rumba is just a beefier Ramps and I know that on Delta printers they have to use an ARM based controller like a Smoothie board to keep up. Sounds like that is what is needed for this too.
     
  8. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
    Smoothieboard X5 are out of stock, I have 5 Stepper drivers on my rumba that I would like to reuse for another board plus a have Reprapdiscount XXL Smart LCD that I would also prefer to reuse on a smoothie board.. do Duet base boards run repetier?
     
  9. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    I believe they do as the designer, I think, was mentioning something about it on the RepRap forums but most people in the RepRap community have left that software now.

    Yeah, Smoothie 5 is always out of stock and honestly it has been a long time since I saw it in stock.

    Question time...Craftbot Plus is now a Core XY based machine and has a color LCD touch screen with a heated build plate that is 25x20x20 cm in build volume for $1099. How much is this printer for all of the parts?
     
  10. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
    thats a good question and im hesitant in generating a BOM, cause then I will know how much I spent LOL
     
  11. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    LOL, ignorance is bliss? :)
     
  12. Ariel Yahni

    Ariel Yahni OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Oct 22, 2015
    Messages:
    144
    Likes Received:
    496
    You can get a compatible smoothie board. Many available.
     
  13. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    Don't suggest a MKS SBASE as those have a lot of issues still.
     
  14. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
    So whats the best Smoothieboard that can use my DRV8825 Drivers and XXL Smart LCD :)
     
  15. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
    finally figured out the problem with my Rumba and Marlin, I had the Serial port set to 3, thinking it was the same thing as the com port setting on my pc, once i set it back to 0, it connected fine
     
  16. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    A logical conclusion as serial port used to mean COMmunications port.
     
  17. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
  18. ekaggrat

    ekaggrat New
    Builder

    Joined:
    Jan 5, 2014
    Messages:
    1
    Likes Received:
    0
    hi, nice bot i must say. i am intending on building a 600 x 600 x 600 build volume bot and liked your approach of a fixed bed. Do you have any pics of printed parts ? How good are they compared to a standard cartasian printer. I recently finished a corexy with a contilevered bed , but the prints are not as good as my delta. so I want to see how good prints do others get.

    thanks.
     
  19. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
    havent gotten that far. waiting for my custom alum plate to show up.
    just updated to RC6Bugfix Marlin and i have some minor revision to some printed parts to do
    once i get it actually printing i will post an update.
     
  20. hernejj

    hernejj New
    Builder

    Joined:
    Apr 10, 2016
    Messages:
    5
    Likes Received:
    0
    Adam,

    Have you found a solution for your belt problem yet? Not sure if you saw, I left some suggestions in the Makerfarm forum.
     
  21. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
    I placed an order for some longer looped belt.. i feel this is the best option. but so far two belts with 2 steppers is working well.
     
  22. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
    Here is a video of it actually printing for the first time.
    it ran into a heating issue.. as the fan was cooling the hotend too much and it couldnt hold its temp
    and went into a thermal shutdown. I like how the BLtouch sensor flashes when someone goes wrong

     
    hernejj and Mark Carew like this.
  23. Ariel Yahni

    Ariel Yahni OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Oct 22, 2015
    Messages:
    144
    Likes Received:
    496
    Thats super fast. What are your speed settings?
     
  24. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
    150mm/sec i believe
     
  25. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
    Finally received a longer loop belt to drive all 4 Z screws. Upgraded to a single Nema 23 Stepper for the Z for the torque
    I will also be adding in Ustepper.com upgrades for the X,Y&Z to turn the steppers into Servos.
     
  26. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
    Single Nema 23 running Quad Acme screws is working well!
    quadscrewn23.jpg
     
  27. GBCues

    GBCues New
    Builder

    Joined:
    Apr 20, 2016
    Messages:
    5
    Likes Received:
    0
    Adam,
    I like this design a lot. Early in the build, you were looking to use a Smoothie Board controller, presumably for the faster CPU. What is it currently running?
    Thanks for any info,
    Gary
     
  28. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
    Currently running on a rumba. Im going to wait until I can get Marlin on a 32bit board before i upgrade.
     
  29. joebot

    joebot New
    Builder

    Joined:
    Jun 29, 2016
    Messages:
    1
    Likes Received:
    2
    Hey Adam,

    About a week ago I started a search for a fixed-bed printer. When I couldn't find one, I started designing one in my head. I finally started my SolidWorks model tonight, and then found this forum after poking around on the openbuilds site. We are designing the same printer! You definitely have a head start, though! I also started with C-beams, but then moved away from them for several reasons. I think I'm going to go with a triple bowden to a diamond hotend. I think you are right on the mark with the NEMA 23 4-screw Z-axis - that's exactly what I was thinking, too. This must be convergent evolution! Anyway, just wondering if you had any updates and/or tips, and if you are planning on sharing your CAD. I hope it's going well!
     
    Adam Filipowicz and Moag like this.
  30. GBCues

    GBCues New
    Builder

    Joined:
    Apr 20, 2016
    Messages:
    5
    Likes Received:
    0
    Hi Adam,
    Well, I've gathered 90% of the pieces and parts to start building this printer. I've been printing the parts with the .stl's from ThingiVerse and doing some initial fitting of the extrusions together. Of course I've had to "undo" them a couple of times or so to insert T-nuts for components yet to come, but those kinds of things are par for the course. So I'm making progress.
    One thing: there are 4 z-screw supports along the top frame that you didn't supply an .stl for - is there any chance of getting you to add that to the files in ThingiVerse? I could draw them up, as an "exercise for the student", but if you still have them handy . . .
    Thanks
    Gary
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice