Welcome to Our Community

Some features disabled for guests. Register Today.

Laser V

Discussion in 'Laser Cutters' started by Robert Hummel, Nov 30, 2013.

  1. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
  2. Woodie49

    Woodie49 New
    Builder

    Joined:
    Feb 7, 2014
    Messages:
    61
    Likes Received:
    1
    Robert, any luck with the full size drawing?
    Thanks
     
  3. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    Still don't have a working printer but have modded the files
    @kram242
    Any idea how he can print full size temps from my drawings ?
    I'm busy figuring out my cam problems :banghead:
     
  4. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,759
    Likes Received:
    2,438
    If you can save them with a scale bar you could take them to Kinko's or Staples. This is how we would print rc airplane plans back in the day before the Phlatprinter :D
    You could also take them to an architect firm that has a large format blueprint printer(same kind that Staples uses) and ask them if they could print it to scale for you.
    Hope this helps
     
  5. Woodie49

    Woodie49 New
    Builder

    Joined:
    Feb 7, 2014
    Messages:
    61
    Likes Received:
    1
    Woun't they fit on a 81/2 x 11 or 81/2 x 15 sheet?
     
  6. bit53b

    bit53b New
    Builder

    Joined:
    Mar 4, 2014
    Messages:
    24
    Likes Received:
    5
    Hi Robert,

    This is an awesome build - very impressed with this and aluminium Ox.
    Just looking through all the files - have I missed a complete circuit diagram? I've seen the layouts and a couple of schematics - I was looking for something that includes the later changes to the board - micro stepping selection / limit switches and the constant 5v enable pin "fix" you mentioned in another thread.
     
  7. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    Ty !
    I have updated the layout to run the relay off the driver board 5v rail but have not posted it yet, I will be building a test board soon.
    The current boards on openbuilds have all the the options but the relay still runs from the arduino's 5v reg so a dedicated usb is needed
     
  8. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,759
    Likes Received:
    2,438
    @Woodie49 Good point I believe they would fit. My guess is that you would need to scale them in photoshop to get them to print properly. Not sure how you would go about it other then maybe the way I did the OX sticker page in SketchUp. The sticker page is 8.5x11 then exported as a 2D jpeg. Opened in Photoshop as a new 8.5x11 doc and then printed full page. This 'sorta' works there are some issues with it coming out perfect.
    Hope this helps
     
  9. bit53b

    bit53b New
    Builder

    Joined:
    Mar 4, 2014
    Messages:
    24
    Likes Received:
    5
    I hope I haven't misunderstood the requirement here, because I'm new to SketchUp as well. But I have been printing plates actual size onto label sheets, so that I can stick them onto aluminium and drill holes.
    Here's what I do: make sure you are in parallel projection (off camera menu). position plate in centre screen and zoom in to fill window (otherwise you may get pagination errors), then choose file->document setup, uncheck "fit view to page", then make sure your print scale is a 1:1 ratio (e.g. I have 1mm in Drawing = 1mm in Model).

    Hope that is useful
     
  10. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    Woodie49 a full set of plates and belt clip hardware are on the way to you 4-10 days hope it helps :)
     
    Mark Carew likes this.
  11. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,759
    Likes Received:
    2,438
    the sticker sheets are a great idea @bit53b Thanks for sharing your printing tips
     
  12. Woodie49

    Woodie49 New
    Builder

    Joined:
    Feb 7, 2014
    Messages:
    61
    Likes Received:
    1
    Robert,
    How much do I owe you?
    Thanks
     
  13. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    Nothing, hope it helps, I only put motor holes in the 1 plate just incase your motors are diff, if they line up as my nema17 do then just use it as a temp plate for the other 2
    You won't need esentrics just the mini v wheel kits, pinch on rail and tighten
     
  14. Woodie49

    Woodie49 New
    Builder

    Joined:
    Feb 7, 2014
    Messages:
    61
    Likes Received:
    1
    Robert,
    I received the Plates today, 3/15. Thanks alot!
    Larry
     
  15. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    No prob, glad they made it :)
     
  16. Woodie49

    Woodie49 New
    Builder

    Joined:
    Feb 7, 2014
    Messages:
    61
    Likes Received:
    1
    What is the bigest size that can be cut, also what is the distance between the laser and the bed?
    Thanks
     
  17. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    My build is 340x340mm cut/etching area
    The distance can be as far as you like as the lens is simply focused to a pin sized dot.
    I would say the thickest you could cut before noticing a slant would be 3mm or so.
     
  18. Woodie49

    Woodie49 New
    Builder

    Joined:
    Feb 7, 2014
    Messages:
    61
    Likes Received:
    1
    That's the cuting area using the 1500mm V-slot ?
     
  19. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    If you are referring to the parts list extrusion length, that is just the suggested length to buy.
    When I get home I will measure the cut lengths I used and post them for you.
     
  20. Woodie49

    Woodie49 New
    Builder

    Joined:
    Feb 7, 2014
    Messages:
    61
    Likes Received:
    1
    That's sounds fine.
     
  21. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    Y rails = 480mm 20x20
    Y rail joining braces = 450mm 20x20
    Repeat for lower section of machine
    X rail = 500mm 20x20
    Joining struts = 80mm 20x40 or longer if you want more space
    Hope that helps :)
     
  22. Woodie49

    Woodie49 New
    Builder

    Joined:
    Feb 7, 2014
    Messages:
    61
    Likes Received:
    1
    Robert,
    Do you have a drawing of how it all go together?
    Thanks, Larr
     
  23. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    Sorry that I do not have but it should be easy for you.
    First assemble/adjust your motor plates and make sure they ride smooth on a stick of 20x20
    Then assemble the x rail with your laser carriage on it, 4 T nuts slide in before you mount the belt clips.
    Mount the clips and run your belts.
    Next you need the spacers and y carriages, bolts go through carriage then spacer and into T nuts.
    After that it's just a matter of adjusting and building the rest of your frame
     
  24. Woodie49

    Woodie49 New
    Builder

    Joined:
    Feb 7, 2014
    Messages:
    61
    Likes Received:
    1
    Do the 450mm rails go inside the 480mm rails? Or the outher way around?
    Thanks
     
  25. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    The 480mm rails go on the outside the two 450mm in between to make a square
     
  26. JCPhlux

    JCPhlux Well-Known
    Builder

    Joined:
    Apr 19, 2014
    Messages:
    209
    Likes Received:
    48
    I have been wanting to build a Laser cutter to cut out FoamBoard this looks like a nice solution. How do I get my hands on one of those sweet laser carriages.
     
  27. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    I designed and built it using sketchup.
    I used custom nema11 motors so won't work for most.
    I designed and cut some nema17 plate for a member but have not seen any progress on his build
     
  28. Woodie49

    Woodie49 New
    Builder

    Joined:
    Feb 7, 2014
    Messages:
    61
    Likes Received:
    1
    I'm working on it slowly.
    The plates for the motors were off a little bit.
     
  29. Robert Hummel

    Robert Hummel Custom Builder
    Moderator

    Joined:
    Nov 14, 2013
    Messages:
    978
    Likes Received:
    715
    In what way? Holes for the motor screws?
     
  30. Woodie49

    Woodie49 New
    Builder

    Joined:
    Feb 7, 2014
    Messages:
    61
    Likes Received:
    1
    In what way? Holes for the motor screws?
    Yes, and the big for the motor could be a little bigger.
    All is fine
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice