HI GUYS ! I have a CNC with a controller however it only sends the code to the back end since we had a power outage this is my g code and in attenchement file you have my backup setting [11:11:09] [ connect ] Detecting Firmware: Method 2 (Ctrl+X) [11:11:09] [ ] Grbl 1.1g ['$' for help] [11:11:11] [ $$ ] $0=10 ;Step pulse time, microseconds [11:11:11] [ $$ ] $1=255 ;Step idle delay, milliseconds [11:11:11] [ $$ ] $2=0 ;Step pulse invert, mask [11:11:11] [ $$ ] $3=7 ;Step direction invert, mask [11:11:11] [ $$ ] $4=1 ;Invert step enable pin, boolean [11:11:11] [ $$ ] $5=0 ;Invert limit pins, boolean/mask [11:11:11] [ $$ ] $6=0 ;Invert probe pin, boolean [11:11:11] [ $$ ] $10=1 ;Status report options, mask [11:11:11] [ $$ ] $11=0.010 ;Junction deviation, millimeters [11:11:11] [ $$ ] $12=0.002 ;Arc tolerance, millimeters [11:11:11] [ $$ ] $13=0 ;Report in inches, boolean [11:11:11] [ $$ ] $20=0 ;Soft limits enable, boolean [11:11:11] [ $$ ] $21=0 ;Hard limits enable, boolean [11:11:11] [ $$ ] $22=0 ;Homing cycle enable, boolean (Grbl) / mask (GrblHAL) [11:11:11] [ $$ ] $23=0 ;Homing direction invert, mask [11:11:11] [ $$ ] $24=25.000 ;Homing locate feed rate, mm/min [11:11:11] [ $$ ] $25=500.000 ;Homing search seek rate, mm/min [11:11:11] [ $$ ] $26=250 ;Homing switch debounce delay, milliseconds [11:11:11] [ $$ ] $27=1.000 ;Homing switch pull-off distance, millimeters [11:11:11] [ $$ ] $30=1000 ;Maximum spindle speed, RPM [11:11:11] [ $$ ] $31=0 ;Minimum spindle speed, RPM [11:11:11] [ $$ ] $32=0 ;Laser-mode enable, boolean [11:11:11] [ $$ ] $100=320.000 ;X-axis steps per millimeter [11:11:11] [ $$ ] $101=320.000 ;Y-axis steps per millimeter [11:11:11] [ $$ ] $102=320.000 ;Z-axis steps per millimeter [11:11:11] [ $$ ] $110=2000.000 ;X-axis maximum rate, mm/min [11:11:11] [ $$ ] $111=2000.000 ;Y-axis maximum rate, mm/min [11:11:11] [ $$ ] $112=500.000 ;Z-axis maximum rate, mm/min [11:11:11] [ $$ ] $120=300.000 ;X-axis acceleration, mm/sec^2 [11:11:11] [ $$ ] $121=300.000 ;Y-axis acceleration, mm/sec^2 [11:11:11] [ $$ ] $122=300.000 ;Z-axis acceleration, mm/sec^2 [11:11:11] [ $$ ] $130=380.000 ;X-axis maximum travel, millimeters [11:11:11] [ $$ ] $131=576.000 ;Y-axis maximum travel, millimeters [11:11:11] [ $$ ] $132=70.000 ;Z-axis maximum travel, millimeters [11:11:11] [ $$ ] ok [11:11:11] [ $I ] [VER:1.1g.20181112:] [11:11:11] [ $I ] [OPT:V,15,128] [11:11:11] [ $I ] ok [11:11:11] [ $G ] [GC:G0 G54 G17 G21 G90 G94 M5 M9 T0 F0 S0] [11:11:11] [ $G ] ok [11:11:12] [ connect ] Firmware Detected: grbl version 1.1g on COM8 [11:11:34] [ GCODE Parser ] GCODE File (from gcode editor) sent to backend
The 4X or the X32? docs:blackbox:start [OpenBuilds Documentation] You forgot to answer CONTROL as in docs:software:openbuilds-control [OpenBuilds Documentation] that is
Right, next up, you said But then posted the Serial log (no GCODE) Can you properly post the GCODE so we can check for you? Use the Upload a File button
The frontend (GUI) sits on top of a backend (Server) that talks to your controller. Thats all exactly fine But your GCODE doesn't start running per your report. So either controller doesn't have power (confirmed) Grbl settings are wrong (But its not) or theres an issue with the gcode And you gcode contains an M6 on line 1, so its not Grbl Compatible. Use a Grbl Compatible CAM/Post please docs:software:overview [OpenBuilds Documentation]
Do you have another computer to try? (Could be something PC specific, we know it works fine for everyone else) Do you have any firewalls, etc that could be blocking comms between frontend and backend?
gcode works ok for me but I predict you are going to have problems in the future because that Gcode has no header that sets the modes looks like metric code, so it should have at least G21 G90 Gcode must always set the modes it expects because it cannot know what happened before it loaded. some macro or previous file may have used inch mode some macro or previous file may have set incremental mode and so on.
unt this time i need to try on other pc because i dont have any firewall and the only error i have are gcode send to backend ... i try this tomorow
Not an ERROR, just a report that the frontend, sent the gcode to the backend for furthe processing. If nothing further happens, its a PC specific problem of some sorts
Good morning, I did one task that was fine after the same problem occurred. I tried with another computer and the problem presented itself as soon as I connected and pressed the play button after all of this test is it my controler ?
I'd still say a PC problem of sorts. Did you reinstall anything else since it worked (firewall, 3rd party antivirus/antimalware, any other applications)
To really rule it out, do you have a different PC at hand you can do a quick test with? If it works on there, controller is fine
Ok, and are you 100% sure your GCODE is Grbl compatible? What if you run the Hello World test? docs:blackbox-4x:hello-world [OpenBuilds Documentation]
after some hours of diag... some little piece of aluminium in drive motor connector ..... so the controler fall in protection mode.. thanks you soo much
