Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

1510

Discussion in 'General Talk' started by Joseph Fitzmaurice, Apr 25, 2021.

  1. Joseph Fitzmaurice

    Joseph Fitzmaurice New
    Builder

    Joined:
    Jun 14, 2020
    Messages:
    29
    Likes Received:
    8
    Hi I have a workbee 1510 belt drive and have upgraded the x axis with a leed screw what setting do I need to change in my black box software thanks as always joe
     
    #1 Joseph Fitzmaurice, Apr 25, 2021
  2. sharmstr

    sharmstr OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 23, 2018
    Messages:
    2,059
    Likes Received:
    1,448
    It depends on the size of the screw. If you go into the settings, there's a calculator next to the X steps per mn setting. Use that, save, then fine tune using the calibration wizard in wizards menu.
     
    #2 sharmstr, Apr 25, 2021
    Peter Van Der Walt likes this.
  3. Joseph Fitzmaurice

    Joseph Fitzmaurice New
    Builder

    Joined:
    Jun 14, 2020
    Messages:
    29
    Likes Received:
    8
    It 8 mm same as the x axis
     
    #3 Joseph Fitzmaurice, Apr 25, 2021
  4. sharmstr

    sharmstr OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 23, 2018
    Messages:
    2,059
    Likes Received:
    1,448
    Then start with the same steps/mm setting. But make sure you also run the calibration wizard to compensate for difference in manufacturing tolerances.
     
    #4 sharmstr, Apr 25, 2021
  5. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    14,877
    Likes Received:
    4,285
    You mean Y right? X is already a leadscrew on the 1510

    If so,
    Set the Y axis steps per mm to 199.1 to start off:

    upload_2021-4-25_22-8-1.png

    Click Save, and Reset when prompted
     
    #5 Peter Van Der Walt, Apr 25, 2021
  6. Joseph Fitzmaurice

    Joseph Fitzmaurice New
    Builder

    Joined:
    Jun 14, 2020
    Messages:
    29
    Likes Received:
    8
    No my openbuild 1510 was belt driven and I now have change the x axis to 8mm screw
     
    #6 Joseph Fitzmaurice, Apr 25, 2021
  7. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    14,877
    Likes Received:
    4,285
    Ok, same as above but set 199.1 into the converted axis which is not currently 199.1
     
    #7 Peter Van Der Walt, Apr 25, 2021
  8. Joseph Fitzmaurice

    Joseph Fitzmaurice New
    Builder

    Joined:
    Jun 14, 2020
    Messages:
    29
    Likes Received:
    8
    Thanks i,s there any other settings I have to change like speed as the belt was much faster than screw joe
     
    #8 Joseph Fitzmaurice, Apr 25, 2021
  9. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    14,877
    Likes Received:
    4,285
    Max rate and acceleration, compare with the other axis
     
    #9 Peter Van Der Walt, Apr 25, 2021

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice