Large inexpensive build that can cut a 4x8 ft sheet with room to spare. Can be built using only a 3D printer and standard parts -- no special CNC'd plates required.

This system allows you to adjust the position of the microphone remotely

This build will use 1/2 inch copper water pipe as the primary material for all structural parts. As of now my intent is a cartesian design drawing from a few popular printers. I'm going to use the least amount of printed parts as possible and locally source as much as I can. I have built an EMT-conduit core-xy printer in the past and while it worked out fine, I feel copper is easier to work, manufactured with more precision, still reasonably inexpensive and will look super cool!

This project produced a movable framed canvas to cover a wall-mounted flat-screen TV when not being viewed, which at the touch of of a switch moves down below the TV and sound bar. The same switch is used afterwards to return the artwork up to cover the TV again. Photo shows mechanism without the canvas frame. See other photos.

Z-Axis for OpenBuilds ACRO system. It is sturdy enough to carry a small drill.

Below are the details of my build and a good story for those who read till the end. Sorry for the grammar

A proper CNC mill conversion. But quite small, with my trademark idiosyncracies.

Major rebuild of my Wanhao Duplicator i3 Plus.

WorkBee1510 with retractable space saving stand and customize build Marlin firmware and MarlinPanel (GCode Sender/UI)

http://www.buildlog.net/sm_laser/drawings.html using this as a baseline.... Going to try and use all or most off the shelf parts.

This is the original C-Beam Sphinx with the 16 wheel X gantry plates. I'm using the Ethernet Smoothstepper, Gecko G540 stepper driver and Mach 4 for motion control.

This is a rework of a previous build I did on here, a mostly printed cartesian CNC. Initially intended to just be an update to that, but so many things changed including the linear motion and every single part has been modified significantly that I felt as though it deserved a whole new build.

This build is the documentation of someone with no experience building the OX cnc machine with a Gecko G540 controller and CNClinux

China Router frame with linear bolts, Nema23 and the icing on the cake “open build parts“

The Sphinx has all the components I need, except it will need a taller vertical lead screw, the same length as the horizontal ones. It will also need legs. So I need to start with the Sphinx parts list, then make a few changes.

Inexpensive plasma table. Accurate, fast, and low maintenance.

A dual extrusion CoreXY printer with a 290 X 290mm build volume built entirely out of 2020 aluminum extrusion and using openbuilds mini-carriages for motion.

This is my first public build. Please be kind. We upgraded our C-Beam to the C-Cbeam X-Large. I want to give special thanks to Moag and the OpenBuilds team for making this happen.

Hobby project

Anti-Twist Design, larger lead screws, enhanced M8 wheel sets.

OX Based CNC

Heavy DIY plasma cutting table

Easy All-in-One Laser and Mounting Kit for your Openbuilds CNC.

The idea was to use materials from previuos failed projects into a succesful one. I have build this tiny but powerfull CNC machine mainly using the universal gantry plates for the X and Y axis. Also another innovative part is the fact that I assembled the Z gantry with 2 aluminum sections of 20X40 and one aluminum seccion of the 20X20. I used NEMA 17 stepper motors with GT2 pulleys. This was designed on Fusion360

I am satisfied with my build and next one will be even better.

This is a remix of Marshal Peck's Voxel OX, with some design tweaks inspired by Makerparts and jjcolletta. It has a build area of 300mm X 300mm X 480mm, but is easily configured for just about any build area up to 500mm X 500mm X 750mm. I have used some laser cut acrylic plates and a couple of 3D printed parts in its construction, however it can be assembled using nothing but OpenBuilds parts with the exception of the heated bed and the Y axis carrier for the heated bed.

Increase Z axis travel by 20-25mm with minimal modifications

This is my first build attempt, a large form (4x4ft.) 3 axis 4-motor CNC router table, . The build components are Baltic birch plywood, stepper motors, SBR linear bearings, and ball screws, LinuxCNC, Mesa controller.

V-Beem horizontal milling machine built on OpenBuilds components. Simple structure, great expansion possibilities, high stiffness.

A Cut To Length machine controlled by computer

An OX-inspired mini desktop mill. Designed in OpenSCAD, these parts are fully parametric and can be customized to your liking.

Textile Drawing Machine is a drawing machine thought specifically to draw on textile. Unlike other CNC machine it's dimensions follow the standard textile dimensions (1500mm) and it's on wheels to allow to draw on an unlimited area. TDM has been developed for the project Digital Wax Print, a self initiated research project, carried out by The Future Continuous, a collabration between Olivia De Gouveia and Eugenia Morpurgo.

A little CNC Sand and Spraycalk drawmaschine More and details in the next weeks

A heavily modified Ox CNC build to replace SO2.

I Like the Sphinx design thought I would attempt my first build. I wanted to build this and use Arduino controller with GRBL to be able to learn and understand my machine.

Hi everyone, im new to the world of lasercutters but i have been granted access for a Trotec laser for a while with old firmware and only compability trought Windows XP. Then i decided to build my own laser, with some easier workflow and support for Windows 10. Since im still a student i have limited resources, so i will try too use scrap parts as much as possible. I will publish photos and updates during my build continously. Gladly taking advices from others.

The X301 is a CoreXY 3D Printer that has a small footprint and a large 300x300x330 build area. The open style of this printer breaks the "Cube" mold of many other printers in this class but still retails rigidity and great performance.

Example model of lead screw driven actuators for your next project!

PeeNaPle_V1.4b is a BoB controller board for 3D Printers, CnC and cartesian machine, using the latest Teensy_4.1

This items are so cool that they need to be together, so I decided to create brackets that connect both pieces together

Rigid variant of the C-Beam sphinx platform

The goal for this bot is to lay down mustard on sausages and burger patties in a smooth and sexy way that looks good for the camera.

Working progress.

This is a machine for placing SMT components on PCBs. It is based on Acro system, off the shelf parts, and a number of custom 3D printed elements.

CNC Hot Wire Foam Cutter. Lathe, Turntable and 4 axis Cutter. Can cut XPS and EPS.

Based on the popular C-beam / V-wheel design, with the largest available work area, relative to machine size. Screw driven with anti-backlash, integrated drag chains, Carbon fibre gantry plates, Openbuilds BlackBox Controller (USB), Transformer & kill switches, with internal wiring, limit switches & Nema 23 motors.

Cartesian style CNC with a working area of around 360mm x 360mm x 120 mm (X, Y, Z) using Linear rails and ball screws. The linear rails are (Hiwin?) HGR 20mm x 520mm and the ball screws are SFU1204 (12mm lead 4mm) of around +/- 430 mm. The base structure is made from rectangular aluminum profiles of 70mm x 45mm x 3mm (thickness of walls).

Fully OpenBuilds based Core XY printer design by Rat Rig. CAD files, build manual, build videos available!

After completing a standard OX build, I found I didn't have enough Z-clearance and designed a set of taller gantry plates

a dual extruder build using direct drive for flexible filaments

This is an arcade "cabinet" of sorts built almost entirely from OpenBuilds extrusions. Save for a few 3d printed parts, the electrical components, the acrylic panels, and the monitor mount, every component was purchased from the OpenBuilds part store.

This is the build of a cartesian 3d printer made of an old Anet and Geeeteck, some 2020 alu profil and linear rail. Powered by a Rumba with a Nextion screen. It should be modular and accept dual Extrusion and laser engraving.

2 days to build Up and running some EMI issues but I think I have them resolved Big shoutout to the community

I made a 5x10 foot cnc out of the parts I bought on this site. It's been upgraded and tinkered with ever since. The end goal is to learn enough to learn to build a large 10x10 foot 3d printer.

A 1000 by 1000 CNC Router with linear rails and a control box.

Large floor or wall mounted plotter design.

Upgraded Z-axis for Sphinx-style CNC using ball screws and linear rails.

The OX-Metal is based on the original OX CNC mill But with a few modifications and add-ons

Contains a further modification to Creality's poor CR-10 design

Z-Axis upgrade with linear rails, SFU1204 Ball Screw and full aluminium construction.

Built from leftover T-Slot extrusions plates and hardware from other defunct projects.

Based on the WorkBee CNC, this is an oversized router built with a specific use-case in mind, for manufacutring beehives, and beehive components

The idea is to make a simple effective ventilator, studying the concept of using a simple push process with and actuator.

The plasma CNC that I have built has a water table that measures 1350mm x 650mm. The water is flooded onto the cut area while cutting and recycled around with a pump. This is to reduce smoke, cool the metal being cut to reduce distortion and also to keep sparks to a minimum. Most of the machine has been made from aluminium , the frame and table from steel, the water table, stainless steel.

How to convert an angle grinder into an electric drill? Remove the angle grinder, leaving only one main motor, and then find a suitable intermediate roller with a point drill to assemble it.

Need cnc to make alumunium sign, brass stamp, etc

My build log of an adapted Sphinx design with additional height and a larger X and Y axis.

CNC Plasma cutter: 608ZZ on steel square tube linear rollers Welded frame HDT2-15 Belt Drive Tradeweld Cut-40 Plasma cutter with converted hand torch Virtual Torch Height Control through inductive probing - open source electronics project

Delta 3d Printer using 3/4" Electrical Metal Tubing (EMT) for Horizontals & 2060 V-Slot for the Verticals and adding a tetrahedron at the top.

A standard 1000x1000 Workbee powered by an X-controller using a Hitachi router

I have the whole description and all the details in the "Body" section!

Build features include a double c-beam gantry (bonded & mechanically fastened), linear x rails, custom gantry end plates, a custom linear rail & ballscrew Z axis, and custom lead screw tensioning plates. The primary goal was to remove twist from the 1500mm gantry & stiffen the Z axis.

Ventilator prototype based of OpenBuilds Stock parts

Using the WorkBee to protect doctors against Corona virus.

This is an automatic cocktail mixer made with 8 small peristaltic pumps. this is driven with the touch screen or over wifi. the controller used is a raspberry pi with a Apache webserver

Two plus years in the making, I finally have a working ACRO 510 laser engraver system complete with enclosure and air filtration.

The Microwave Filter Tuner (MFT) combined with the University of Regina’s tuning algorithm automatically tunes microwave filters by using a custom CNC machine with a computer vision system for identifying, mapping, and tuning each filter element, providing improved consistency, flexibility, and accuracy compared to traditional methods. The MFT is low cost and is capable of tuning multiple filter configurations with minimal preparation.

Custom painting machine in designed and wrote the software for. Paintings are with acrylic color on canvas

A robust Core XY style 3D printer that has a clean parallel belt implementation and whose dimensions are adaptable to meet builder's needs. The use of open builds V-slot and other open hardware make customization easy.

Current progress uses existing openbuilds bearings, but also uses 8mm shafts (custom)

Small Machining Vise designed around 20x80 Openbuilds Rail System

The main objective is to build a software which can completely run on a single board computer, Rasbperry Pi, to reduce the complete cost of building a cnc machine. The software is extensively tested and can be run on any raspberry pi 2/3 boards. With no G-Code dependency, you can do complex 3D relief carving to simple tasks with simple GUI based project development environment. Please go through the YouTube channel for more details https://youtu.be/8KOXqLpvscg

This build is about a model train lift in a secure and dust free storage. It is a roll on/roll off concept for a model train layout.

A sun cutter only using mirror and glass balls with x and y table movement

A cool little CNC router build that uses the V-Slot belt & pinion drive and stock parts.

laser mini 20 * 40 OPENBUILDS base frame.(크기 412x455mm) laser mini 20*40 기본프레임입니다. 기존 여러부품을 사용한 제품보다 부품수를 줄이면서 최소한의 단가를 뽑을려고 디자인했습니다.. 기존대비 부품수 절반에 단가도 절반을 줄이면서 최적의성능을 내려합니다.

My take on the LEAD CNC build. Followed the instructions and I think it came together very nicely. Added a few of my own touches to finish up the build.

This is a work in progress ACROS build with new legs and wire tracks.

This is a lead 1010 build that I wanted to have a little fun with. I purchased the whole Lead 1010 kit, and felt like studying a few shortcomings of the original to see if I can improve it or just have some fun with it.

A simple to assemble, super clean and safe PSU case solution that fits into the OpenBuilds wire management ecosystem

Get organized with the SharkBits Holder!

Larger format FDM printer using C-Beam linear stages

C-Beam machine - 1000mm base.

A new design of my based on a couple different machines I have seen both on openbuilds and youtube. In the end will have a and X/Y workspace of 1250mm x 1000mm and a Z axis range of about 200mm.

This EggBot design has a perfect functionality (the same as the original EggBot professional), a perfect cable and microcontroller arrangement, and a perfect cost as it uses a minimum list of parts (with one V-Slot Linear Rail size20mm x 80mm and length 500mm you can build 3 EggBots!)

What I'm doing is pretty self explanatory. I've put a few pictures up

A Benchtop Plasma Cutter Concept

Built a 32"x40" ACRO Kit for my 10watt Endurance Laser. Put it in a stand alone clamshell cabinet, added a 340cfm 6" fan and variable speed switch for the fan. Using LIght Burn for my primary software. It seems to be work well.

A C-Beam machine design, strengthened with extra brackets and plates. GRBL controlled, opto-isolated inputs, jogging box.

A Prusa i3 design running on Open Build's mini V wheels